The manual is embedded in the build instructions for the various Align kits. This appears to come out of the manual. At least its identical to. i have just ordered an Align 3gx flybarless control unit but i can’t find any instructions online anywhere as i like to usually download and print. I have put together the written info on the Align 3GX v I found so far. Mostly for my own memory. I shrunk this info to a Pocket Guide that I will printout (or read.
|Published (Last):||5 December 2004|
|PDF File Size:||11.96 Mb|
|ePub File Size:||14.26 Mb|
|Price:||Free* [*Free Regsitration Required]|
I shrunk this info to a Pocket Guide that I will printout or read on my mobile if I have to change the parameters through the 3GX unit out in the field. This excellent control feel will allow pilot of all skill levels to experience the aalign integration between 3GX and helicopter.
Actual gain value differs amongst servos and helicopters. Please double check this. REV begin to flash in sequence. This setup mode sets the elevator gyro direction Tilt the helicopter forward and check if swashplate is tilting correctly toward the back.
Only right aileron and front elevator allign is needed. Are you sure you don’t remove the bind plug after powering down? Go to Flybarless System “Direct mode bypassing gyro, for mechanical travel and neutral point setup” to adjust the level of the swashplate and then re-complete the setup. Preview the software and read everything and get familiarized with it.
In addition to transmitter, the anti-torque compensation feature can also be set through 3GX interface’s rudder parameter. Originally Posted by Tulo. Se “Trottle Calibration” at the alig. Originally Posted by bad What software, this software.
The goal is to find the maximum gain without tail hunting. I also found this site: Then you remove the bind plug and power down. Subsequent setup laign is entered by a single press of the SET button.
Proper frame rate must be selected based on your servo’s specifications. Register Now In order to be able to post messages on the HeliFreak forums, you must first register. The recommended collective pitch range for various T-Rex helicopters is degress depending on preferenses.
Originally Posted by Tulo I haven’t been able to find the bind procedure, can anyone help me out?? Should any changes made to the endpoints or subtrims on the transmitter in the future, the 3GX flybarless system initial setup must be performed again. Settings export feature allows custom settings to be shared amongst friends. Reset throttle curve and pitch curve to default That’s kinda what I figured thanks!
This setup mode sets the elevator gyro direction. With 3GX in operation mode, push rudder to left or right, and press the SET button for about a second. Plug in flight battery 3. For tail pitch adjustment, center the rudder servo by either setting the 3GX flybarless to normal rate mode msnual lockor press and hold the SET button for 2 seconds.
Cool, I appreciate the help! Power on Futaba 10C 5. Quote message in reply? Wait for some sort of jingle or series of flashing lights then release bind button Does that sound right? Check that there is no binding throughout the pitch range 3. Tilt the helicopter forward and check if manuao is tilting correctly toward the back. Setting swashplate acceleration may increase the burst amp draw of servos. The control unit will determine the maximum aileron endpoints. Therefore, BEC output capability should be confirmed to handle burst current when setting collective pitch acceleration, otherwise insufficient current supply may result a,ign flight accidents.
The throttle stick position where main pitch is 0 degree must be maintained. The more dampening effect, the smoother helicopter flies, but feels less direct. This is clearly noticeable in stable hover as well as highly aerobatic routines. Tilt the helicopter right as shown in diagramand check if swashplate is tilting correctly toward the left. Align 3GX version 2. 3gs
3GX manual – HeliFreak
Adjust the servo neutral point and main blade pitch. The trim must be zero when using 3GX, and should not be adjusted at anytime. Are there pages missing?
My HK 3GX setup. Pirouetting flips type of maneuvers are easily accomplished with precision. While keeping swashplate level and main pitch at zero degrees, press the SET button to register the neutral point and enter E. Hem 3GX v 2.
Align 3gx pdf manual
It is the instructions. Support with APS gyro system and bring up more functions for your helicopter. Push bind button my spektrum tx module 4. If im not mistaken I believe Futaba does not make satellites for there receivers or one that is compatible with the 3gx.