Site Loader

CCNP ROUTE Instructor Lab Manual. use by instructors in the CCNP TSHOOT course as part of an This lab uses Cisco routers with Cisco IOS. CCNP TSHOOT Student Lab Manual. Share? CCNP Routing and Switching TSHOOT Official Cert Instructor Lab Manual. Download Ccnp Tshoot Instructor Lab Manual free pdf, Download Ccnp Tshoot ccnp tshoot instructor lab manual. this document is exclusive property of.

Author: Guzilkree Malajar
Country: Spain
Language: English (Spanish)
Genre: Technology
Published (Last): 19 August 2017
Pages: 357
PDF File Size: 15.53 Mb
ePub File Size: 17.77 Mb
ISBN: 345-8-26363-456-9
Downloads: 25133
Price: Free* [*Free Regsitration Required]
Uploader: Kigalabar

Review the lab topology together with your team members. The focus of this lab is to allow the students to familiarize themselves with the lab environment. Encapsulation is set to isl on physical interfaces but port channel 2 is set to dot1q. The most direct approach to tracking the traffic is to capture packets at set points along the path by using a packet sniffer. To get a more detailed description of the type of inconsistency and what might be causing it, you can examine the output of the show spanning-tree inconsistentports command.

P2p or Shr to indicate the link type typically based on duplex status — P2p is full-duplex and Shr is half-duplex or shared Ethernet. Console access requires no username or password.

Even if you cannot find the underlying cause of the problem yourself, by reducing the scope of the problem, you have a better-defined problem that can be escalated to the next level of support. Router interface designations from the physical topology diagram are provided.

It gives you a starting point for gathering information about what is actually happening on the network, and it makes it easier to spot abnormal behavior.


Propose a hypothesis possible cause.

The table does not include any other type of interface, even though a specific router might contain one. However, if the switches that you are using have the capability to track packet statistics for access lists, you might be able to write an access list that matches the specific traffic that you are manua in and isolate the traffic statistics for that type of traffic.

Read ccnp-tshoot-instructor-lab-manual

Using the procedure described in Labverify that the lab configuration files are present in flash. Section 2 of this lab includes sample troubleshooting flows, useful commands, and examples of output. Is dynamic or static routing being used? Reload the device, but do not save the system configuration if prompted. If yes, describe their function. Copy the specified lab device configuration file from flash to the running config.

The lab configuration files for the course should be in flash under the tshoot directory for a given device.

The baseline configurations for all devices are included at the end of this lab. This command shows you whether the VLAN exists and which ports are assigned to it.

If time is a factor, Tasks 1 through 3 can be done in one session and Tasks 4 through majual in a subsequent session. Displays device ID and type and confirms that a link is operational at the data link layer in both directions, including the sending and receiving ports.


See Task 1, Step 2 for device access methods, usernames, and passwords after the configuration amnual have been loaded. Is the VLAN allowed on the trunk between the switches? This preserves the no shutdown commands for interfaces. The configs for this lab include ip host name ip-addr entries for all devices. Another useful option is show mac-address-table interface intf-id, which shows which MAC addresses were learned on a specific port.


CCNP TSHOOT 6.0 Student Lab Manual

Map the subnet scheme to the logical diagram. Which switch is the root switch for each VLAN, and what are the configured spanning-tree priorities? Use only the number of the last octet for IP addresses in the diagram.

Instructors can use a TFTP server, USB drive, flash memory card or other method to copy all the course configuration files into the flash: Troubleshooting approaches to select from include the follow-the-path, spot-the-differences, bottom-up, top-down, divide-and-conquer, shoot-from-the-hip, and move-the-problem methods. Document the logical topology to support future troubleshooting tasks.

To access privileged EXEC mode, use the enable password of ciscoenpa When the network is properly configured, all devices send archives of their running configurations to this server whenever the running config is copied to the startup config. Displays all essential parameters that affect the topology, such as root port, designated ports, port state, and port type, as well as the spanning-tree mode implemented. Identify all host devices that are members of each VLAN.

Document the physical topology to support future troubleshooting tasks. Ping from ALS1 to R2 at instryctor