Site Loader

E3 TO E ACCORDING TO IEC E E E E E E E E E E E E E E E6. E3. E 1,0. 1,1. 1,2. 1,3. 1,5. 1,6. 1,8. 2,0. 2,2. 2,4. 2,7. 3,0. 3,3. 3,6. 3,9. 4,3. 4,7. 5,1. 5,6. 6,2. 6,8. 7,5. 8,2. 9,1. E 1,0. 1, 1,1. 1, 1, 1, 1, 1,4. 1, Buy Condenser for BMW 6 (E24) from VAN Wezel, NRF, AKS Dasis, Thermotec, Frigair and other manufacturers of spare parts for Air conditioner of BMW cheap.

Author: Vuramar Shaktirn
Country: Australia
Language: English (Spanish)
Genre: Software
Published (Last): 14 June 2006
Pages: 228
PDF File Size: 10.65 Mb
ePub File Size: 4.29 Mb
ISBN: 514-1-97502-124-9
Downloads: 49696
Price: Free* [*Free Regsitration Required]
Uploader: Yozshugore

E6 E12 E24 E48 E96 E The Electronic Industries Association Reiueand other authorities, specify standard values for resistors, sometimes referred to as the “preferred value” system.

For analogue designs it is a little more flexibility is often needed, but even E6 or E12 standard resistor values can be used without difficulty in the design. The E3 series resistors are the most widely used and hence these values will be the most common resistor values used within the electronics industry. By using this site, you agree to the Terms of Use and Privacy Policy. The EIA Electrical Industries Association which is based in North America is one organisation that has adopted the system and as a result the resistor value series are often referred to as the EIA standard resistor values.

Erihe Standard Resistor Series 1. Resistor E series The EIA preferred values or standard resistor values can be summarised in a tabular form to give the different values within each decade.

Standard Resistor Values: E3, E6, E12, E24, E48

In the early 20th centurycapacitor previously called condenser [1] [2] and resistor [3] [4] value increments were different than today. Current resistor technology enables very close tolerance levels to be achieved, yet there is still a great benefit in using resistors even from the E3 series.

  DIMITRI KHALEZOV THE THIRD TRUTH PDF

Other types of electrical components are either specified by the Renard series for example fuses or are defined in reihw product standards for example IEC for wires. This page was last edited on 1 November2e4 Currently, most electrolytic capacitors are manufactured with values in the E6 or E12 series, thus E3 series is likely obsolete. The exact value is of little is of little consequence and the value can be maintained within the E3 series.

However, this is not always the case as can be seen by comparing the E24 and E96 lists. The ohm resistor has a value ranging between and ohms. Wikimedia Commons has media related to E12 values. Commons category link is on Wikidata Commons category link is on Wikidata using P The series are as follows: In other projects Wikimedia Commons. As transistor radio production migrated towards Japan during the s, it was critical for the electronic industry to have international standards.

E6 Standard Resistor Series 1. Archived PDF from the original on This process is followed through for all the values in a decade, creating a set of standard resistor values for each tolerance.

E12 Standard Resistor Series 1. The E series preferred or standard resistor value ranges are internationally accepted and have been adopted by international standards organisations.

Views Read Edit View history. Also, reige E series is used for 0.

Standard Resistor Values | E3 E6 E12, E24, E48 Series | Electronics Notes

The standard resistor values are organised into a set of series of values known rehe the E-series. It should be noted that some values in the E24 series don’t exist in E48 to E series.

  JURNAL ATRESIA ANI PDF

The values in any decade can be derived by merely dividing or multiplying the table entries by powers of The E3 series is defined as a series of the numbers 1. R24 EIA “E” series specify the preferred values for various tolerances. These standard resistor values have a logarithmically based sequence and this enables the different values to be spaced in such a way that reeihe relate to the component tolerance or accuracy.

From Wikipedia, the free encyclopedia. If a manufacturer sold resistors with E3 series values in a range of 1 ohm to 10 megohms, then the available resistance values would be: The rationale is simple – select values for components based reibe the tolerances with which they are able to be manufactured. In any event, one should be aware of these practices to avoid confusion. While the “E” preferred value lists are the best way to insure one is stocking the optimum number of values for a given tolerance, a word of caution is in order with respect to what is actually available in the marketplace and certain real world practices.

E3 has three resistors in each decade, E6 has six, E12 has twelve, reohe so forth. Below are the common resistor values. They provide a wider range of common resistor values that can e42 used. One example where values can be kept within the E3 series occurs with digital design where a pull up or pull down resistor is needed.