Site Loader

Fenner Taper Lock® bushes are machined in cast iron and steel and are available in a full range of both metric and Imperial bores and keyways. They ha. You can find the largest assortment Taper Lock bushes metric bore at ERIKS. Choose from FENNER Taper Lock® bush metric bore size · Taper Lock® . Fenner Taper-Lock Weld-on Hubs are easy to install and are entirely suitable for use. where severe operating conditions are met. Tightening the screws.

Author: Taubei Samuzuru
Country: Norway
Language: English (Spanish)
Genre: Music
Published (Last): 28 March 2014
Pages: 235
PDF File Size: 15.50 Mb
ePub File Size: 1.50 Mb
ISBN: 733-1-94113-430-3
Downloads: 18750
Price: Free* [*Free Regsitration Required]
Uploader: Mirg

Each hole will be threaded on one side only.

To view the demonstration video showing installation and removal of a Taper Lock bush, please Yaper Below. Warranty As per Fenner’s policy. Ensure that the Taper Lock bush is free in the hub, then slip the assembly onto the shaft and locate in the desired position. How to Fit a Taper Lock Bush.

Oil threads, the point of the set screws or threads, and under the head of the cap screws. Thank you for the request. If the bushing does not loosen immediately, tap on the hub to assist remove. Expected price per piece. The outside of the bush is tapered to match the component bore that is to be located on the shaft. The Taper Lock bush needs to be thoroughly cleaned, removing all traces of oil, grease, dirt, and metal filings.


Fenner Taper Lock Bush

Ensure that there is no oil or lubricant between the taper on the outside of the lodk and the taper bore of the hub, to which tapr bushing is being installed. We have sent you an email enclosing confirmation link, on your ID. Using a hammer and block, or sleeve, against the large end of the Taper Lock bush will help to avoid damage to the bushing. The Martin and Fenner Taper Lock bushes featuring the fourth hole make them a preferred option in higher speed applications where balancing of the drive is critical.

Your password has been reset successfully.

Buy Fenner Taper Lock Bush Pulleys (TLB Size ) Online in India at Best Prices

Pack of 1 pieces. Many other manufacturers generally manufacture Taper Lock bushes with an odd number of holes. In sizes where washers are found under the screw head, be sure to use these washers. Please share your feedback and help us improve!


Ensure there is an air gap between the top of the key and the bushing keyway slot. Screws should be tapsr alternately and evenly until all screws are pulled up and the bushing is square into the hub. Please enter correct email. Taper bushes are available in both imperial and metric shaft sizes, ranging from 0. We will get back to fenenr shortly! Tighten the screws alternately until the bushing is loosened in the hub.


Installation of a Taper Lock Bush. Both Martin and Fenner Taper Lock bushes are manufactured in their full range of bushes with an even number of holes, i.

Continue Browsing Continue to login. The Taper lock bush is manufactured llck precision cast iron, and is machined to a high quality finish.

This information is available from the installation sheet that accompanies any new Taper Lock bush. The Taper Lock bush is pre-bored and keyed to match the required shaft and keyway diameters. Check the bushing to ensure all surfaces are free from nicks and burrs, and ensure the bushing has no signs of cracking or fatigue. Please Enter your contact details to continue Please enter your phone number.

Then place the screws loosely into the holes that are threaded on the hub-side, as shown in Figure 1 below. You browser has Javascript turned off! Taper Lock Bush Venner.

Email this to frnner friend or colleague! This will prevent cracking of the bush. Last sold on Rs. Clean the shaft, the bore, the outside of the bushing, and the bore of the hub in which the bush is to be installed into, ensuring the bush is removed from the hub, should it already be installed.