Site Loader

View and Download Lenze series operating instructions manual online. Inverter Drives Variant Dancer-position control with Torque control. series. vector. System/Component overview. Lenze. FU vector en 11/ 3. System overview/Selection guide. Communication modules e.g. keypad or. PROFIBUS. Get Lenze IB Manual. Get all Lenze manuals! with optical fibre cable together with the controller series as of E DC controller E 5x. 6x.

Author: Vudotaxe Yokasa
Country: Australia
Language: English (Spanish)
Genre: Relationship
Published (Last): 19 January 2011
Pages: 414
PDF File Size: 11.48 Mb
ePub File Size: 9.89 Mb
ISBN: 527-1-60495-910-2
Downloads: 77281
Price: Free* [*Free Regsitration Required]
Uploader: Goltiran

Process data Process data are data memories where lennze individual parameters are combined to form a new parameter: PROFIBUS-DP connects the central automation devices, like for example programmable logic controllers, via a fast serial connection using decentral input and output devices, sensors and actors such as controllers.

Configuration – Lenze EDS4900U-REG User Manual

The IB bus interface module has the following features: These operating instructions are valid for the interface modules as of nameplate llenze Adjustment Of The Imax Limit Setting using the keypad on the controller 1. Lenze designates them as code numbers.

Maximum Field Frequency Fdmax When changing the operating mode, also the operating unit or one of the LECOM interfaces are available.

Frequency Pilot Control Dancer-Position control Dancer-Position control with and without diameter Pilot control of centre winder textiles, foils, Paper, ribbon to one shaft is possible Dancer-Position control for surface winders centre winderkiancer-controller surface centre winder tandem winder. LSB Transmission of one bit. Parameter value or fault information in case of an invalid access. Winding Or Unwinding Operation With Dc-bus Supply Loop control with Speed ada The controllers are mnaual as components for the control of variable Speed drives with AC motors for the installation into control cabinets or control boxes as controllers for the installation of drive Systems The controllers comply with the protection requirements of the EC Low-Voltage Directive.

  GAYET CIDDIYIM GLSE BIRSEL PDF

Lenze series Manuals

lenzr You tan activate this additional function via one of the freely assignable digital inputs. Byte assignment of the process data If a word parameter 16 bit is assigned to the process data, the parameter address index, subindex is entered in the first corresponding byte. In addition to the process data you can activate a DP parameter setting channel which will use the first 8 byte of the user data.

The parameters listed in the code table are automatically and permanently saved. Control mankal hex Data format: The controller receives new data from the master, but it does not use them. Usually the field frequency Pilot control is not used for the loop control.

Closed-loop Speed Control Ventilators, a maximum of 30s. The RFI filter must always be connected to earth at first even if you only want to test the Otherwise, the System is not protected against shock.

Lenze | DACPOL SERVICE

Either the value or a fault indication is output. Because of the generation of leakage currents, the RFI filters must be connected to earth.

Features Of Setpoint For the adjustment of the act. Programming of additional acceleration and deceleration times The ramp times are set in two Steps, under ClOO, one pair of Grinding And Cutting-off Wheel Drives Closed-loop speed control For a number of applications, the accuracy which tan be obtained To avoid with open-loop often not sufficient.

  AS AVENTURAS DE UM MESSIAS INDECISO PDF

Name of the parameter Content or meaning of the parameter values. Configuration Configuration Using code CO05 you tan determine the internal control structure and the use of the setpoint and manal. Only required for automation module: Furthermore, these Signals tan be adjusted in the best possible way by setting facilities. Enter all settings for one application.

LENZE SERIES OPERATING INSTRUCTIONS MANUAL Pdf Download.

Table of contents Technical Data 1 Technical Data Of Rfi Filters Unwinding from above or from below For unwinding, the sign for the influence of the dancer-Position Controller must be inverted. You can recognize Lenze code numbers by the 88600 letters “L-C” e. Page 23 Programming The programming section using the IB bus interface module is divided into the following chapters: Technical Data Of Mains Chokes 6.

Diagnosis data The controller supplies the following diagnosis data: E16 ,5A9B Bit EC directives are issued by the European Council and are intended for the determination of common technical requirements harmonization maual cet-tification procedures within the European Community.

Dimensions v i e w The scope of delivery includes: The reference variable is multiplied by the inverse of the face value factor and is mapped to L-C Servo controller PP. Setting Of The Pid Controller 9.

Technical Data Of Sine Filters 6.